- Works with the engine in the frame (most dial gauges are too large and won't fit in the RD due to the frame rails sitting just above the heads)
- Metric Gauge - no need to convert from SAE and one less chance to make a mistake when converting
- Increments:
- 10mm stroke 1/100mm graduation
- Big hand sweeps 1 mm
- Smal hand in .10 mm increments
- 10, 12, & 14mm adapters makes this kit suitable for most 2 strokes
- 2 Extensions
-
Out of stock
We designed these new kits with RD enthusiasts in mind and includes the following specs / features -
Kill Switch - Open type for Vape/MZB/Powerdynamo ignitions running no battery. Momentary type kill switch, kills engine when button is pressed. Includes 24" wire. Handlebar tupe mount. -
Vape Coil for systems 71 05 799 00 & 71 05 999 00 & others. Sold each. Front and back pictured. (This part also used for same ignition system sold under the brand names Powerdynamo/MZB) -
Vape Coil frame mount coil bracket. (This part also used for same ignition system sold under the brand names Powerdynamo/MZB) -
Vape Coil Wire Boot, sold each. (This part also used for same ignition system sold under the brand names Powerdynamo/MZB) -
Vape Ignition - Hardware Upgrade for Yamaha RD250/350/400/R5/DS6/DS7 (Street ignition Version) 71 05 799 00. The hardware supplied by Vape includes a washer that easily deflects when tightened. Our hardware upgrade kit includes a thicker washer 4.5mm, longer zinc plated 7x 35mm rotor bolt and an additional stainless washer. The thicker washer will not deflect when tightening the rotor bolt. (This part also used for same ignition system sold under the brand names Powerdynamo/MZB). -
Vape Pick Up Coil (Sensor) S01T. (This part also used for same ignition system sold under the brand names Powerdynamo/MZB) -
Vape Pick-up Coil Shim Plate, sold each. (This part also used for same ignition system sold under the brand names Powerdynamo/MZB) -
Vape Plug Wire Set - Non Resistor Type. (This part also used for same ignition system sold under the brand names Powerdynamo/MZB) -
Vape Rotor Puller Tool for use with Powerdynamo ignition system. (This part also used for same ignition system sold under the brand names Powerdynamo/MZB). Inner M12 x 90mm Outer M27 x 1.25 pitch -
Vape Regulator for use with Powerdynamo RD street ignition. (This part also used for same ignition system sold under the brand names Powerdynamo/MZB) -
Vape Regulator with built in battery eliminator (capacitor) for use with vape RD street ignition when running without a battery. (This part also used for same ignition system sold under the brand names Powerdynamo/MZB). -
Vape Relay for use with Powerdynamo RD Street Ignition. (This part also used for same ignition system sold under the brand names Powerdynamo/MZB) -
Vape Rotor - Replacement rotor for Vape RD street ignition. One piece CNC machined rotor with ramped trigger that helps prevent the possibility of the engine starting in reverse direction. (This part also used for same ignition system sold under the brand names Powerdynamo/MZB) -
Vape Stator (For systems 71 05 799 & 71 05 999). (This part also used for same ignition system sold under the brand names Powerdynamo/MZB) -
Yamaha RD, RZ, R5, TZ - Generator Wiring Grommet. Reproduction part no longer available from Yamaha. Excellent high quality replacment part, chemical resistant, creates a dust and water tight seal. These can be used with the stock wiring or when replacing the ignition with the Powerdyanmo system.